Model 2600

3 1/2 DIGIT PANEL METER
WITH PLUG-IN OPTION BOARDS
Models
Options
Features
Model 2600
Specifications
Rear View With Option Board Installed
Case size: "D"


MODELRANGEINPUTPRICE
26000 to ± 1999See input Voltage Range$254.00
26000 to ± 1999See input Current Range$254.00

Prices subject to change without notice.
Top of page


OPTIONSDESCRIPTIONPRICE
  • 01
See process current $40.00
  • 02
See process volts$40.00
  • 03
See RMS AC volts or current$35.00
See TRMS AC volts or current$55.00
Prices subject to change without notice.
Top of page


FEATURES

  • Dummy zero for 4 1/2 digit display
  • NEMA 4 front bezel
  • Process volts option board
  • Process current option board, 4-20mA or 10-50mA
  • RMS AC option board
  • Excitation option for transducer (24 VDC)
  • TRMS AC option board
  • Fast/Slow filter select
  • All option boards easily installed
  • Base unit is multi-range 3 1/2 digit voltmeter or current meter
  • All range and decimal point selection easily accessible on the rear
  • Standard 1/8 DIN short depth (3.8") case
  • 115/230 switch selectable power
  • Removable screw terminal connector block
  • DC power options
  • Process current loss indication
meter 2600
MODEL 2600
Top of page

MODEL 2600
The Series 2600 is a new low cost 3 1/2 Digit Panel meter which uses the mother/daughter board concept to produce a multi-function meter. All option boards are plug in type, no soldering required, and range programming is done with solderless jumpers on the rear. Fine calibration is done with two potentiometers on the rear and coarse calibration is done with solderless jumpers on the rear. All decimal points and the dummy zero are programmable via solderless jumpers on the rear of the unit. Ease of programming and function change using the daughter board concept makes the 2600 a unit that can be stocked by the OEM and easily adapted for various functions.

Top of page

REAR VIEW WITH OPTION BOARD INSTALLED

REAR VIEW WITHOUT OPTION BOARD INSTALLED

Top of page

SPECIFICATIONS
Base Unit:
  • DC volts/DC current
Display:
  • 4 1/2 digit .56" LED with Polarity and three decimal points (±1.9.9.90)
Accuracy:
  • .05% of reading ± one LSD. Temperature coefficient ±.015% of full scale per degree Celsius
Input Impedance:
  • 1 MEG ohm (voltage) .1 ohm to 100 ohms (current)
Input Voltage Ranges:
  • 0 - 199.9mV
  • 0 - 1.999V
  • 0 - 19.99V
  • 0 - 199.9V
Input Current Ranges:
  • 0 - 1.999mA
  • 0 - 19.99mA
  • 0 - 199.9mA
  • 0 - 1.999 Amps
Fine Span Adjustment:
  • ±5%
Fine Zero Adjustment:
  • ±5%

Roller Error:

  • (Difference between plus and minus readings) 2 counts maximum, typically 1 count
Input Configuration:
  • Single ended bipolar
Power:
  • 115 or 230 VAC, ± 10% at 47 to 400Hz (switch selectable)
Operating Temp Range:
  • -20C to +60C
Storage Temp Range:
  • -40C to +85C
Mechanical:
  • 1/8 din short depth aluminum case (4.0") with ABS bezel and gasket for NEMA 4 rating. Case size D" refer to page 39.
I/O Terminations::
  • Pluggable screw terminal block
Conversion Rate:
  • 2 1/2 times per second
Fast/Slow Filter Select:
  • Jumper on rear adds filter circuit to reduce response time for step input from 1 second to 10 seconds.
Top of page

OPTION BOARD SPECIFICATIONS
PROCESS CURRENT 4-20mA OR 10-50 mA (PI)

Drop Resistor:

  • 4-20mA 49.9
  • 10-50mA 20
Span Adjustment Range:
  • +100 to +1999 (assuming zero offset)
Offset Adjustment Range:
  • -1000 to +1000
  • Coarse adjustment of span and offset accomplished with solderless jumpers on rear of unit. Fine adjustment is done with two 20 turn potentiometers on rear.
Loss of Signal Indication:
  • Front panel LED comes on if signal falls below 3mA (9mA) or above 21mA (51mA)
Excitation Output:
  • +24VDC ±20% at 50mA, unregulated (optional)
On Board Calibration:
  • Jumper on rear selects on board reference to calibrate unit for approximately 80% of full scale
Top of page

PROCESS VOLTS (PV)
0-5VDC, 0-10VDC, 0-20VDC

Input Impedance:

  • 1 MEG ohm
Offset Adjustment Range:
  • -1000 to +1000
  • Coarse adjustment of span and offset accomplished with solderless jumpers on rear of unit. Fine adjustment is done with two 20 turn potentiometers on rear.
Excitation Output:
  • +24VDC ±20% at 50mA, unregulated (optional)
Top of page

RMS AC VOLTS OR CURRENT
Accuracy:
  • ±1% of reading ±2 counts of LSD
Input Impedance:
  • 1 MEG ohm (Voltage) .1 ohm to 100 ohms (current)
Frequency Input Range:
  • 47Hz to 1000Hz
Input Voltage:
  • 0 to 199.9mV
  • 0 to 1.999V
  • 0 to 19.99V
  • 0 to 199.9V
Input Current:
  • 0 to 1.999mA
  • 0 to 19.99mA
  • 0 to 199.9mA
  • 0 to 1.999 Amps
  • Input range selectable by solderless jumper on rear of unit.
Top of page

TRMS AC VOLTS OR CURRENT
Accuracy:
  • ±5% of reading ±2 counts of LSD
Input impedance:
  • 1 MEG ohm (Voltage) .1 ohm to 100 ohms (current)
Frequency Input Range:
  • 47Hz to 1000Hz
Input Voltage:
  • 0 to 199.9mV
  • 0 to 1.999V
  • 0 to 19.99V
  • 0 to 199.9V
Input Current:
  • 0 to 1.999mA
  • 0 to 19.99mA
  • 0 to 199.9mA
  • 0 to 1.999 Amps
  • Input range selectable by solderless jumper on rear of unit.
Top of page

CASE SIZE: "D"