MODEL 8010

TIMER/COUNTER BI-DIRECTIONAL COUNTER
FREQUENCY METER/TACHOMETER
Model
Options
Features
Model 8010
Specifications
Case size: "A"


MODELRANGEINPUTPRICE
80100 to ± 1999999 0 to 5k Hz$406.00

Prices subject to change without notice.
Top of page

OPTIONSDESCRIPTIONPRICE
  • 01
ASCII RS232 compatible output $80.00
  • 02
ASCII RS422 compatible output $80.00
  • 05
5VDC input power $15.00
  • 08
Input amplifier for sine wave/pulse input signals.
Adjustable threshold 		$30.00
  • 10
Remove front panel start/stop/reset switches$15.00
  • 11
Differential line receiver input for count inputs$30.00
  • 12
10 - 15VDC input power$20.00
  • 18
Reset switch only$15.00
  • 19
Excitation output 5VDC at 150mA. Nonvolatile memory for displayed count not operable when this option is installed$20.00
  • 22
230VAC ±10%, 50-400hz, input power. $15.00
  • 23
Green LED display $60.00
  • 24
10 - 30VDC input power $60.00
  • 25
Special legends and/or logo,(Special artwork to be supplied by customer). One time charge $100.00
    		Plus per lens $ 15.00
    • 26
    		No logo. $ 15.00
    • 27
    		Screw terminal I/O connector. $40.00
    • 28
    		Blank lens. $ 15.00
    • 29
    		25 pin "D" connector for RS232 interface $20.00
    • 31
    		"SECONDS" legend $15.00
    • 33
    		"MINUTES" legend $15.00
    • 34
    		"HR/MINUTES/SECONDS" legend $15.00
    • 35
    		"MILLISECONDS" legend $15.00
    • 36
    		"COUNTER" legend $15.00
    • 37
    		"RPM" legend $ 15.00
    • 38
    		"DEG/MIN/SEC" legend $ 15.00
    • 39
    		"DEG/MIN" legend $ 15.00
    • 50
    		Sunlight readable .6" LED display. No polarity available.$40.00
    Prices subject to change without notice.
    Top of page


    FEATURES

    • IBM PCTM compatible RS232 or RS422 output (optional)
    • Front panel and remote inputs for start, stop, reset, and setup
    • Up to 5 KHz count rate
    • Timer resolutions down to 1 millisecond
    • Microprocessor based unit programmable for different modes of operation
    • 6 1/2 digits of display
    • Four limit set points
    • Count stored indefinitely after loss of power without battery
    		Series 200C
    Top of page

    MODEL 8010
    The Model 8010 is a new microprocessor based Counter/Timer with Optional RS232 or RS422 outputs which facilitate easy interfacing to computers or programmable controllers. The 8010 can be programmed for all models of operation from the front panel switches. Timer ranges are 1999.999 sec, 1999.99 sec, 19999.9 sec, 199.59 hr/min/sec, 19999.99 min, and 1999.999 min which are programmable via the front panel switches or the remote inputs.

    Top of page

    SPECIFICATIONS
    Accuracy:(Timer) Crystal time base,
    ± 2 PPM/degrees Celsius from zero to fifty degrees Celsius. Totalizer accuracy ± 1 digit. Tachometer accuracy ± digit, ± 1 X 10.5 time base accuracy.

    Display:
    6 1/2 digits. .56" high efficiency red LED ± 1999999. Decimal points are user programmable.

    Controls:
    Front panel start, stop and reset pushbutton switches which are also used to set limits and multiplier.

    Remote Inputs:
    Start/stop and reset signals: require closure to logic common or TTL logic zero. Input loading one LPTTL load. Can also be used to set limits and multiplier.

    Outputs:
    ASCII RS232 compatible: (optional) ASCII RS422 compatible: (optional) Programmable baud rates. Baud Rates: 300, 1200, 9600.

    Limit Outputs:
    TTL compatible output can be programmed to go high or low at limit and hold until reset. Will drive 4 TTL loads. Limits are set by putting unit in setup mode and then toggling through numbers.

    Sine Wave/Pulse Count Input:
    (option-08). Minimum signal 150mVRMS DC to 5 KHz. Maximum signal 115VAC without damage to circuitry. Input impedance 100 Kohm.

    TTL Count Input:
    Schmitt trigger type with no limit on rise or fall time of input pulse. Maximum count rate 5 KHz, input loading one LPTTL load.

    Power:
    115VAC 50-400 Hz, 8 watts maximum
    5VDC power 500mA maximum (Optional)
    10 - 15VCD power 400mA maximum (Optional)
    230VAC 50-400 Hz, 8 watts maximum (Optional)
    10 - 30VDC power 400mA maximum (optional)

    I/O Method:
    Card edge connector with solder tabs. (supplied) 25 pin sub-miniature "D" connector for RS232/RS422 output. (optional)

    Top of page

    CASE SIZE: "A"