MODEL 9600A

MODEL 9600A

LVDT/RVDT READOUT CONTROLLER Models
Options
Features
Model 9600A
Specifications
Case size: "D"

MODEL	PRICE
9600	$403.00

Prices subject to change without notice.
Top of page

OPTIONS	DESCRIPTION	PRICE
01	RS232 Compatible Interface	$60.00
02	RS485 Compatible Interface	$60.00
05	5VDC input power. 500mA max.	$135.00
09	Analog output 0 to ą 5VDC	$90.00
09	Analog output, (0-10VDC) tracks input	$60.00
11	Parallel BCD with I/O connector	$65.00
12	9-18VDC power 400mA max	$135.00
13	Parallel binary with I/O connector	$65.00
22	230VAC; 50-400hz input power.	$15.00
24	18-36VDC power 300mA max	$135.00
50	Sunlight readable red LED	$40.00

Prices subject to change without notice.
Top of page

FEATURES

Eight software selectable sensitivity settings
Splash proof bezel with panel gasket seal
1/8 DIN heavy duty aluminum case
Programming and calibration from four front panel switches
Optional analog output, 0 to ±5VDC
4 1/2 digits, .56 3/4 red LED readout with negative indication
Two high speed setpoints with open collector outputs
Optional RS232 or RS485 interface
Optional parallel BCD output
AC excitation for LVDT
100% Digital zero suppression
Selectable excitation frequencies, 2.5Khz, 5Khz, 7.5Khz, or 10Khz
Selectable filter, 250hz or 1000hz cutoff
Phase adjustment

MODEL 9600A

Top of page

MODEL 9600A
The series 9600 is versatile readout/controller designed to be used with AC excited LVDT type transducers. It combines a constant amplitude carrier generator, a stable carrier amplifier, and a full wave synchronous demodulator. The zero point can be offset by up to 100% of full scale and the full scale reading can be programmed to be virtually any number between 100 and 19999 counts. Optional analog outputs, parallel BCD and serial interfaces are available which make this unit a versatile low cost unit. Two limit points with open collector outputs are standard. Response time of the limits is dependent on filter selection and is 1msec. or 4msec. The series 9600 is housed in a rugged 1/8 DIN aluminum enclosure with NEMA 4 front bezel and panel gasket seal.

Top of page

SPECIFICATIONS
Power requirements:

AC: 105 VAC to 132VAC @ 50mA (47 to 500 Hz)
AC: 198VAC to 264VAC @ 25mA (47 to 500 Hz) optional.

Display:

Type: Five digit, seven segment LED 0.56" (14.3 mm) high indicator
Polarity Indication:"-" Displayed
Overrange Indication: Thermocouple display shows "OPEN"

Environmental:

Operating Temperature Range: -20°C to +60°C
Storage Temperature Range: -25°C to +85°C
Relative Humidity: 0% to 90%, Non-condensing

Dimensions:

Case size "D" Case D dimensions
Weight: 1 pound
I/O Terminations: Fifteen quick disconnect terminals

Analog to Digital Conversion:

Technique: 16 Bit Sigma Delta
Rate: 3 Conversions/Second

Analog Output: (optional)

Voltage: 0 to ±5VDC. 0V and 5V points are programmable via front panel switches. Maximum drive capability ±2mA.
Response time 4msec. or 1msec. dependent on filter selection.
CMV: 1400V Peak (AC or DC) Peak Between Analog Output Ground and AC Power Line Ground.

Serial Interface: (optional)

ASCII RS232 or RS 485 compatible (optional); format: 1 start bit, 8 data bits, 1 stop bit, and no parity bits. Baud rates: 9600, 4800, 2400, 1200,600, 300, 150, & 75 programmable from the front panel. Output compatible with DCI Model 9100 remote readout.

Parallel BCD Output:(optional)